Momentum Modbus Plus 170 PNT Series Guía de usuario Pagina 183
- Pagina / 376
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Configuring an M1 CPU with Modsoft
870USE10110 July 2004 183
Changing the Number of Segments for M1 CPUs with Modsoft
Introduction The number of segments specified in the Configuration Overview screen determines
the number of I/O map drops that you will be able to set up for your CPU.
The number of segments you will need depends on whether your processor adapter
will support an I/O bus network.
For I/OBus
Networks
You must change the number of segments to 2 if you want to create an I/O map to
support an I/O bus network.
For All Other
Cases
The default number of segments (1) is correct. You only need one drop because the
only points to be I/O mapped are those on the local base.
Procedure From the Configuration Overview screen, follow the steps below to change the
number of segments.
Step Action
1 From the Overview menu, select I/O.
Result: The cursor will appear in the I/O field of the editor on the number of
segments.
2 Type the new number of segments.
3 Push <Enter>.
Utility
OverView
I/OMap Ports Segmnts Loadable Quit
F1
F2
F6
F7 Lev 8
PLC :
PLC Type MOMNTUM
Model M1
System Memory 12.0K
Extended Memory K
Size of Full Logic Area 11532
No. of I/O Map Words 00032
Specials :
Battery Coil 0-----
Timer Register 4-----
Time of Day clock 4-----
Cfg. Extension Used/Size 0/ 0
0xxxx <-> SFC None
F8 OFF F9F3 F4 F5
CONFIGURATION OVERVIEW
Cfg Ext
Ranges :
0xxxx 000001 - 001536
1xxxx 100001 - 100512
3xxxx 300001 - 300048
4xxxx 400001 - 401872
4xxxx <-> SFC None
Dupl. Coils Start: 0-----
I/O : I/O Type MOMENTUM
Number of Sefments 1
IO ap Reserved Words 32
- Momentum M1 Processor 1
- Adapter and Option Adapter 1
- User Guide 1
- Table of Contents 3
- 4 870USE10110 July 2004 4
- 870USE10110 July 2004 5 5
- 6 870USE10110 July 2004 6
- 870USE10110 July 2004 7 7
- 8 870USE10110 July 2004 8
- 870USE10110 July 2004 9 9
- 10 870USE10110 July 2004 10
- Safety Information 11
- About the Book 13
- Getting Started 16
- Overview of Momentum M1 17
- Processor Adapters 17
- Label Description 19
- 1 Standard port connector 19
- 3 LED indicators 19
- 870USE10110 July 2004 21 21
- Memory Size and 22
- Clock Speed 22
- Input and Output 23
- References 23
- 1 Modbus Port 1 connector 26
- 2 LED indicators 26
- 870USE10110 July 2004 27 27
- 870USE10110 July 2004 31 31
- 2 I/0Bus port connector 32
- 870USE10110 July 2004 33 33
- 870USE10110 July 2004 37 37
- 2 Modbus Port 2 connector 38
- 870USE10110 July 2004 39 39
- 870USE10110 July 2004 43 43
- 1 Ethernet port connector 44
- 2 I/OBus port connector 44
- 3LED indicators 44
- 870USE10110 July 2004 45 45
- 870USE10110 July 2004 47 47
- 870USE10110 July 2004 51 51
- 870USE10110 July 2004 55 55
- 870USE10110 July 2004 57 57
- 870USE10110 July 2004 59 59
- 870USE10110 July 2004 61 61
- Overview of 63
- Momentum Option Adapters 63
- 870USE10110 July 2004 67 67
- 172 JNN 210 32 68
- Serial Option 68
- Adapter 68
- Specifications 68
- 1 LED indicator 70
- 2 Battery compartment door 70
- 870USE10110 July 2004 71 71
- 172 PNN 210 22 72
- 870USE10110 July 2004 73 73
- (A Momentum Component) 74
- 870USE10110 July 2004 75 75
- 870USE10110 July 2004 77 77
- 870USE10110 July 2004 79 79
- Assembling 81
- 870USE10110 July 2004 83 83
- Procedure: 84
- Assembling an 84
- Adapter and an 84
- I/O Base 84
- 870USE10110 July 2004 85 85
- Removing an 87
- Adapter from an 87
- 870USE10110 July 2004 89 89
- 870USE10110 July 2004 91 91
- I/O base 93
- 2 Lift off the adapter 95
- Installation Guidelines 96
- 870USE10110 July 2004 97 97
- 3.4 Labeling the M1 CPU 99
- 870USE10110 July 2004 100
- Communication Ports on 101
- Momentum Components 101
- Communication Ports 102
- Using the Modbus Ports for 103
- 4.1 Modbus Port 1 104
- Using the Modbus Ports 105
- 4.2 Modbus Port 2 109
- Interconnect 119
- Components 122
- Modbus RS485 126
- Connector T 126
- (RJ45 Base) 126
- Using the Modbus Plus Ports 130
- Standard Cabling Schemes 132
- Cluster Mode Cabling Schemes 134
- Cluster 136
- Scheme #1 136
- Scheme #2 137
- Cable Between 139
- Clusters 139
- Terminating 143
- Resistor Plugs 143
- Using the Ethernet Port on 149
- Ethernet Port 150
- Using the Ethernet Port 151
- Transmission 162
- Transmission errors table 162
- Using the I/O Bus Port for 163
- Networks Momentum 163
- Using the I/O Bus Port 164
- Modsoft and Momentum 171
- Configuring an M1 CPU with 173
- Overview 174
- 870USE10110 July 2004 175 175
- Magnum 176
- Step Action 176
- 870USE10110 July 2004 177 177
- 2 Push <Enter> 178
- 870USE10110 July 2004 179 179
- Defaults for an 180
- 18.0 Adapter 180
- 870USE10110 July 2004 181 181
- 870USE10110 July 2004 183 183
- 870USE10110 July 2004 185 185
- Adapters 187
- Specials : 189
- Battery Coil 001536 189
- Timer Register 4 189
- 870USE10110 July 2004 191 191
- Port Parameters with Modsoft 193
- Should Not Be Changed 195
- 870USE10110 July 2004 197 197
- Using Modsoft 198
- Components Using Modsoft 199
- Adapters with Modsoft 203
- 870USE10110 July 2004 205 205
- At a Glance 207
- 870USE10110 July 2004 211 211
- 870USE10110 July 2004 213 213
- Configuring a Modbus Plus 215
- 10.1 Getting Started 216
- Modsoft) 220
- 3 Push <Enter> 222
- 870USE10110 July 2004 223 223
- 870USE10110 July 2004 227 227
- 870USE10110 July 2004 229 229
- 870USE10110 July 2004 231 231
- Completed 233
- Screen: Node 5 233
- (Using Modsoft) 235
- 870USE10110 July 2004 237 237
- 870USE10110 July 2004 239 239
- Defining the 240
- Global Inputs 240
- 870USE10110 July 2004 241 241
- Push <Enter> 242
- Defining Global 244
- 870USE10110 July 2004 245 245
- 870USE10110 July 2004 247 247
- 870USE10110 July 2004 249 249
- Saving to Flash 252
- Concept and Momentum 255
- 870USE10110 July 2004 259 259
- 870USE10110 July 2004 261 261
- 870USE10110 July 2004 263 263
- 870USE10110 July 2004 265 265
- 870USE10110 July 2004 267 267
- Default 144 words 268
- Minimum 4 words 268
- 870USE10110 July 2004 269 269
- 870USE10110 July 2004 271 271
- 870USE10110 July 2004 275 275
- 870USE10110 July 2004 277 277
- 870USE10110 July 2004 279 279
- 870USE10110 July 2004 281 281
- Using Concept 282
- Changing Mode and Data Bits 283
- 870USE10110 July 2004 285 285
- Changing the Modbus Address 287
- I/O Scanning 289
- Subnet Mask: 291
- Master Module (Slot): 291
- Health Block (1X/3X): 291
- (Using Concept) 292
- Components (Using Concept) 293
- Diagnostic Block (3X/4X): 295
- 171 CCC 980 20-984 295
- As shown below: 297
- 870USE10110 July 2004 299 299
- Editing the Local 301
- I/O map 301
- 2 Click on the Insert button 305
- Drop dialog appears 306
- 870USE10110 July 2004 307 307
- 870USE10110 July 2004 309 309
- 14.1 Getting Started 312
- Accessing the 313
- 870USE10110 July 2004 315 315
- Option Effect 316
- Devices on the Network 318
- 870USE10110 July 2004 321 321
- Cop dialog box 322
- 5 Click <OK> 332
- 870USE10110 July 2004 333 333
- Global Outputs 336
- Saving to Flash in Concept 337
- ProWORX32 and Momentum 341
- Configuring an M1 with 343
- ProWORX32 343
- File Edit View Window Help 344
- ProWORX 32 - [RIO_test] 344
- Modbus Plus Gateway TCP/IP 345
- 870USE10110 July 2004 347 347
- Hardware Clock 348
- Registers 348
- 870USE10110 July 2004 349 349
- Selecting the 350
- 870USE10110 July 2004 351 351
- 870USE10110 July 2004 353 353
- Appendices 357
- Ladder Logic Elements and 359
- Instructions 359
- Ladder Logic 360
- Standard Ladder 361
- A Special STAT Instruction 363
- Words Description 364
- 4 Not used 364
- 870USE10110 July 2004 365 365
- 16151413121110987654321 366
- 1 = ATI healthy 366
- 0 = ATI Not Healthy 366
- Error Codes 367
- Battery Life Information for 369
- Alkaline Batteries 369
- 870USE10110 July 2004 371 371
- Numerics 373
- 870USE10110 July 2004 375 375
© 2020, manymanuals.es. Todos los derechos reservados | 0.084 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales